Peugeot 208 Key Replacement
It is better to leave the replacement of Peugeot 208 keys to auto locksmiths equipped with the equipment and knowledge. They will be able to make and program new keys much quicker than a dealership and at a lower cost.
If the key fob has stopped locking or unlocking your doors, it could be due to a dead coin battery. There are other reasons why the key might be malfunctioning.
Dead Coin Battery
A dead coin battery will stop your Peugeot 208 from locking and unlocking, and also preventing it from starting the engine. In this instance, you will need to make use of the alternative method for starting found in your vehicle's owner's manual.
The spark plugs may also be worn out. The spark plugs light the fuel to start the engine. However, they have a limited lifespan. If they aren't used enough they will eventually fail.
There is a simple solution for this issue. The best way to solve this issue is to test the voltage of your car battery with a multimeter. If the voltage falls below 11,5 volts, then it's time to replace it. If the battery is corroded it is crucial to clean its contacts. This can be accomplished by removing the rubber cover from the two battery terminals, and then using a wirebrush to remove any corroded parts of the battery. After that, you need to connect the positive and negative pole cables.
Water Damage
If your 208 won't start and the battery hasn't been replaced, you must inspect the spark plugs. It is possible that they're overly dirty, causing them to not to spark. The spark plugs can be cleaned in an workshop.
Peugeot cars are equipped with a key with a transponder that is compatible with the immobiliser. This ensures that only the correct key can start the engine. If the chip in the Peugeot key is damaged, it will not transmit the correct signal to the vehicle.
This is a very common issue that is caused by water damage. This is a common issue in more cold climates where the car is exposed to rain or snow. In this case, contact an experienced locksmith who will have the tools and equipment required to reprogram the key. They will also have the most up-to-date technology and the machinery needed to make a Peugeot 208 smart key. The process should not take more than 15 minutes.
Contacts to the battery are not working properly.
Peugeot replaced the transponder chips by introducing a new type that uses electronic components mounted on a circuit board. The new system is excellent when it's new, but the circuit boards deteriorate over time and stop working properly.
This could stop the immobiliser from working, so your vehicle won't be able to start. If this happens, it's a good idea to get in touch with a Peugeot specialist or locksmith.
Another common issue is when the battery in the key fob is dying, this causes the key blade to stop from entering the lock. A locksmith for cars can replace the battery and cut a fresh blade for you, this is generally a quick fix.
Faulty Receiver Module
It could be that the receiver module is defective when your Peugeot key fob doesn't work after being dropped on the floor, or exposed to a stormy rainstorm, or accidentally washed. The receiver module is responsible for transmitting radio signals to the onboard computer that manages the central locking system of your Peugeot vehicle.
The key fob itself has rubber seals that prevent water from reaching the electronic chip inside. However prolonged exposure to water can break through these seals, causing damage to the chip. Submerging the key fob into ocean water on the beach or throwing it into the water can be especially damaging because of the high salt content.
The module will need to be replaced if your Peugeot spare key is no longer working. This should be done by a Peugeot specialist or a professional auto locksmith. As opposed to other cars, Peugeot keys are protected by a unique immobilizer system that requires the correct code for the start of the engine. This is why it is imperative that you should only rely on an authorized Peugeot locksmith to design and program the replacement.
Computers with faulty on-board computers
The on-board computer of your Peugeot is responsible many systems inside your car, including power windows and airbags. If something goes wrong with these systems, it'll typically display a code that indicates the issue. This code will be stored in the system until the issue is fixed. Most often, this involves replacing the onboard computer.
The most frequent cause for the warning light for airbags to come on is corroded or loose connections within the sensor. This could be due to wear and tear, ageing or exposure to salt and moisture. It is crucial to get this issue addressed as quickly as possible, as an airbag that is malfunctioning can be dangerous in the event of an accident.
If peugeot 206 key replacement G28 see the error "card not found" on your Peugeot, the key battery inside the key fob could be dead or weak. This will stop the key fob sending a signal that will disable your vehicle's immobilizer. You can test this by pressing the unlock button on the key fob and then trying to start your vehicle. If this doesn't work the battery on the key is in need of replacement.